Dell Alienware m17 R4 disassembly

-

Needed to change the keyboard on my Dell Alienware m17 R4 and couldn't find images online to prepare myself for what will need to do when I started. So I took them while I was in the process of doing it, to help someone else in the future.

And here are two advices before starting.

1) There is one connector where you need be extra careful. You can see it at image 1 with blue arrow. It is glued with black tape over it so don't try to remove it quickly or you will broke the upper plastic of the connector.



Image 1 - week connector!

2) You will need very small screwdriver to remove keyboard at the end. Don't start with dissembling the laptop if you don't have one.

Dell Alienware m17 R4 disassembly 1

Dell Alienware m17 R4 disassembly 2

Dell Alienware m17 R4 wifi

Dell Alienware m17 R4 battery

Dell Alienware m17 R4 keyboard


 

If this saves you some time or a connector, you can thank me by buying me a coffee.

Buy Me A Coffee



Comments

Post a Comment

Popular posts from this blog

AUTOSAR and CRC calculation

-
Image
If you find yourself reading AUTOSAR document Specification of CRC Routines you are probably looking for a solution on how to implement it in your code. This is short instruction without explaining how CRC works. It includes working CRC code with examples from the mentioned documentation. Explanation of CRC8 CRC 8 it means, the polynomial of CRC is 8 bit long.  Explaining chapter 7.2.1: CRC result width - it is the return value, it says it is 8 bits long Polynomial - this value is used to calculate CRC. In this case, it is 0x1D Initial value - CRC calculation start with this value. It is usually all F's or zeros.  Input data reflection - it says if the data which you want to do CRC need to be reflected or not. Example of data reflection: hex: 0x73 or binary: 1110011, reflected value is: 1100111 or hex 0x67 Result data reflected - same as input data, but the only result is reflected XOR value - result value need to be XOR-ed with this value before is r
Read more

Flashing/debugging/running code at external memory in the memory-mapped mode

-
Image
  STM32 microcontrollers have special capabilities running code directly from external flash. To make it possible STM32 made a special set of instructions called memory-mapped mode where the microcontroller is reading instructions from the external flash. Since to read data from an external flash can take some time there is QSPI protocol witch basically four wires used as SPI MISO (Master Input Slave Output) to make throughput 4x time faster than classical SPI.   Figure 1 - Illustration of STM32H750 connected to W25Q128JV 
Read more

Debugging EK-TM4C123GXL with Visual Studio Code on Linux

-
Image
If you have TM4C123G LaunchPad Evaluation Kit and you like Visual Studio Code here is how to setup debugging on this board. This is the tutorial how to do that on clean Ubuntu 16.04 LTS. ARM GCC Compiler Setup Download the latest GCC cross compiler for the ARM from here:  https://launchpad.net/gcc-arm-embedded/+download In the time of writing this text, the last one is    gcc-arm-none-eabi-5_4-2016q3-20160926-linux.tar.bz2 Run this commands in Linux console. wget https://launchpad.net/gcc-arm-embedded/5.0/5-2016-q3-update/+download/gcc-arm-none-eabi-5_4-2016q3-20160926-linux.tar.bz2 tar -jxf gcc-arm-none-eabi-5_4-2016q3-20160926-linux.tar.bz2 rm gcc-arm-none-eabi-5_4-2016q3-20160926-linux.tar.bz2 exportline="export PATH=$HOME/gcc-arm-none-eabi-5_4-2016q3/bin:\$PATH" echo $exportline >> ~/.profile source ~/.profile sudo dpkg --add-architecture i386 sudo apt-get update sudo apt-get install libc6:i386 lib32ncurses5 Without i386 architecture you will
Read more